How To Set Up A Hammock Stand

DIY Lite: Build a Backyard Hammock Stand from Scratch

Build this outdoor hammock stand in an afternoon—only in time to take a nice long nap in the dominicus!

Photo: Ohoh Blog for Bob Vila

Wish that you had a relaxing moment in a camping hammock in your own backyard, merely have nowhere to hang it? Rather than wait years for ii copse to grow large plenty to anchor it, solve this problem before the end of summertime by building a DIY hammock stand. Made from a few planks of lumber, this hammock stand is lightweight enough to pull toward whatsoever shady corner—fifty-fifty follow the shade throughout the afternoon—notwithstanding sturdy enough so that any grown adult tin can enjoy nap fourth dimension once once again.

Photograph: Ohoh Blog for Bob Vila

MATERIALS AND TOOLS Available on Amazon
– ii×iv lumber (7 8footlong pieces)
– Gear up square
–  Round saw
– Sandpaper
– Forest clamps
– Power drill
– 6inch hex bolts with basics (12)
– Washers (24)
– Wood glue
– three½inch screws (6)
– 4inch metallic brackets (4)
– 2inch screws (24)
– Exteriorgrade wood stain
– Varnish (optional)
– Paintbrush
– Hitch rings with plate (two)
– 3/eight″ spring link (2)

Footstep 1

Photo: Ohoh Blog for Bob Vila

The first thing to practice is cut all the lumber to the dimensions needed for the projection. To make what we'll go along to refer to as the "base of operations" of the DIY hammock stand, you will need two 8-foot-long 2×4s.

Lay them and so that the three-½-inch sides (remember, a 2×iv isn'texactly 2 inches by 4 inches) balance apartment on the floor. Then, use a set up square to help yous make mirroring 30-degree angle cuts at each cease of the boards. You'll pencil lines from the top left and top right corners of each plank at a 30-degree angle in toward the center, so cutting. Sand down your lumber, paying particular attending to the sawn ends.

Annotation: Y'all'll brand several cuts at 30- and 60-degree angles during this project. If you don't ain a fancy power saw, you tin utilize a gear up square and a hand saw instead.

Pace 2

Photograph: Ohoh Blog for Bob Vila

Next, cut 2 2×4s in half to make 4 "lateral posts," each with one flat and one angled end. To brand these cuts without whatever woods scraps, measure and mark the exact middle of each length of lumber—at 4 anxiety in, and and then 1-3/4 inches downwardly. Lay your fix square over the centre dot so that you can draw a line at a 30-degree angle direct through your mark. Draw a line at a xxx-degree bending, and cut. Sand down your cut pieces.

STEP iii

Photo: Ohoh Blog for Bob Vila

At present, y'all'll create "camber timbers" to connect the base and lateral posts for extra support (see the diagram in Step 4). Take one of the couple remaining ii×4s, measure to observe its center (over again: at 4 feet in, and then 1-3/four inches downwardly). Draw a line at a sixty-caste bending through the center, and cut following the line. You'll accept two pieces of woods of the same length, each with one end at lx-degree angle.

Cut the straight end of each slice at a sixty-caste angle, besides, simply one that is a mirror image. Sand down all of the pieces.

STEP 4

Photo: Ohoh Blog for Bob Vila

Cut iv 15-inch pieces from another of the remaining ii×4s. Get out two pieces with 90-degree cuts on either end; you'll use those to join the top office of the lateral posts. The other two should each have one terminate flat and the other cut at a 30-degree angle (then that the cuts mirror each other); those two volition strengthen where the base of operations meets the lateral posts. Sand them completely.

On a flat surface, start laying out the planks co-ordinate to the diagram in a higher place to build the DIY hammock stand:

• Start with the one base lumber (its longer side should face) and a lateral post on each side, touching only non overlapping.
• Then lay a camber timber diagonally to connect the lateral post and base of operations; where the slant timber's end overlaps the base should be about twenty inches in from the base's end.
• Finally, position the four 15-inch cuts: two (without angles) on tiptop of the lateral posts and 2 (with angles) overlapping where the base of operations and the lateral post run across.

Footstep 5

Photo: Ohoh Blog for Bob Vila

Now, start to actually assemble the construction with bolts, beginning at i finish. (You'll come across we started on the right side.)

Agree the pieces of the in-progress hammock stand with clamps as you lot and drill pilot holes through both layers of both woods. Y'all'll want to drill as direct every bit possible to hands pass the bolts through afterward. Drill two holes through the top of the stacked 15-inch pieces and lateral posts, 1 hole through each end of the slant timbers, and ii holes through each of the 15-inch cuts joining the base and the lateral post.

Repeat on the other side, and then that you end up with 12 holes total.

STEP 6

Photo: Ohoh Blog for Bob Vila

Now, lay out your remaining cuts—the second base of operations wood and the 2 unused lateral posts—as y'all did in Step 4, only without any 15-inch pieces.

As the drill bit is not long enough to drill through three layers of 2×4s to join both sides of the DIY hammock stand, you lot need to precisely mark the holes you've just completed onto your remaining materials. Lay the already bored base and slant timbers over meridian of them, and use your drill to mark the holes' locations. Remove the wood you've already drilled in Step 5, and consummate the holes where you've marked. Again, call up to drill equally straight as possible.

STEP 7

Photo: Ohoh Blog for Bob Vila

Thread a 6-inch hex commodities with washer through each hole in the commencement half of the structure that you lot created in Steps 4 and 5, assembling any overlapping layers as previously explained. Utilise a fiddling wood glue between each piece of lumber.

Stop past laying the 2nd base and the two lateral postal service on peak. Cap each bolt with a washer and a nut, in that gild, so tighten.

Step viii

Photo: Ohoh Blog for Bob Vila

Wait until the glue dries before flipping the structure vertically. Then, add 2 feet to steady the DIY hammock stand up. You lot'll cut your last 2×4 in half to make them.

At the middle of one of the iv-human foot-long pieces, cut a notch into the 3-1⁄2-inch-broad side of the 2×4 that measures 1-inch deep and 4-1⁄2 inches broad (most as wide as your hammock stand up measures afterward assembly) using a wood chisel and hammer.

Repeat to make a 2d foot for the opposite end of your hammock stand, and so sand both pieces.

STEP 9

Photograph: Ohoh Blog for Bob Vila

On the showtime human foot, line the notch with forest gum, then plough two×four so that its 3-1⁄2-inch side remains flat to the ground and slide it up to fit the notch snugly effectually the bottom of the hammock stand. Drill pilot holes for three 3-one⁄2-inch screws. Then, affix metal brackets (using iv 2-inch screws apiece) to connect the pes to the lateral post on each side of the stand.

Repeat with the second foot.

STEP 10

Photo: Ohoh Blog for Bob Vila

Almost done! This is what your DIY hammock stand should look similar at this point.

Step 11

Photo: Ohoh Blog for Bob Vila

Apply a coat of exterior forest stain in the colour of your choice to protect the wood from the wet information technology'll encounter outdoors, working the stain in the management of the grain with your brush. If you cull an oil-based stain, use a natural-bristle brush; for latex stains, use a synthetic-bristle brush. And so, leave the wood to dry out for the amount of fourth dimension suggested on the stain's package (likely 24 hours).

If you don't have a specially formulated outside wood stain to aid weatherproof your lawn projection, you lot can choose any standard wood stain followed by at least two coats of varnish instead.

STEP 12

Photo: Ohoh Blog for Bob Vila

Finally, to hang the hammock, fasten a hitch ring with four two-inch screws into the acme of each end (over where the lateral posts sandwich a xv-inch-long plank). Then apply a three/viii″ jump link—1 that specifies a working load limit of at least a couple hundred pounds—at either end to claw the hammock to the hitch ring. Last, only not least, climb on in and enjoy the view from your new DIY hammock stand.

Photo: Ohoh Weblog for Bob Vila

Photograph: Ohoh Blog for Bob Vila

Photo: Ohoh Blog for Bob Vila

Photo: Ohoh Web log for Bob Vila

Ama is a DIY aficionado and the creative mind behind Ohoh Blog. She likes home decor, lighting, and furniture projects that may involve painting, sewing, drilling…no matter the technique! Whatever she has on hand is inspiration to create, and fodder for her serious addiction to upcycling.

Source: https://www.bobvila.com/articles/diy-hammock-stand/

Share this post